Call Us: (973) 256-3000 Plast-O-Matic Valves, Inc.
1384 Pompton Avenue
Cedar Grove, NJ 07009 USA
Email:

High Performance Pressure Regulators 1/4" through 4" Sizes
Series PRH

Designed for higher flow capacities...achieved with less system pressure loss.
Machined Body with Molded or Machined Spring Housing.

pressure regulators with traditional machined bodies

Advantages:
Series PRH offers the highest available performance in a standard, spring-type regulator -- please scroll below to see the competitive test results. Based on the same large area frictionless rolling diaphragm, poppet seat, isolated pressure sensing chamber and pressure balanced shaft of Series PR, this valve uses higher capacity springs and an expanded base to accomodate the increased pressure settings.

• Downstream pressure setting is infinitely adjustable from 10 psi to 125 psi.
• Maximum inlet pressure is 150 psi.
• Sizes 1/4", 3" and 4" in PVC.
• Size 1/4" in CPVC
•尺寸自然Polypro 1/4“3”。注3" size in Polypro is limited to 5-50 PSI set pressure.
• Sizes 1/4", 1/2", 3/4", 1", 1 1/2" in PTFE. Note the 1 1/2" size in PTFE is limited to 5-50 PSI set pressure.
• Sizes 1/4", & 3" in PVDF.
• Balanced shaft provides smooth, non-stick operation; assures reliable service for millions of cycles.
• Large surface area of the frictionless diaphragm provides exceptional sensitivity.
• Double u-cups prevent leakage along the shaft and eliminate the possibility of "creep".
• Designed for low maintenance and easy to adjust.
• High capacity, heavy-duty design.

pressure regulators with traditional machined bodiesCorrosion resistant, also excellent for high purity and water applications. The standard connections are female NPT threaded ports. Socket, flanged and spigot connections are also available. Springs (not wetted) are steel. Adjusting bolts and external fasteners are stainless steel. Optional Xylan coated springs and fasteners available; consult factory. Some Kynar PVDF components are used in the Natural Polypropylene and PTFE models for strength. Adjusting bolt and lock nut on 3" pressure regulator is HDPE.

Pressure and flow performance of Series PRH exceeds that of any available spring-loaded thermoplastic pressure regulator, as the chart below indicates. For complete flow performance curves for specific sizes, and test results vs. specific competitive valves, please contact our Technical Group at (973) 256-3000.


Pressure Regulator Performance Curves -- Flow Capacity vs. Pressure Drop-off

Comparison of Plast-O-Matic vs. Competitive Regulators

flow performance curves of series prh pressure regulator versus competitive valves

下降的区别是再保险的压力gulator set pressure and the actual downstream pressure.
Test Parameters -- Inlet Pressure: 70 PSI. Set Pressure: 35 PSI. Media: Tap Water. Temperature: 65 F/18.5 C. Valve size: 3/4" machined body PRH.

3" PRH Performance Curves

flow performance curves of series prh 3 inch pressure regulator

4" PRH Performance Curves

flow performance curves of series prh 4 inch pressure regulator

Important Notes --Dashed lines in curves above exceed the recommended maximum flow rate of 5 feet per second for thermoplastic piping.
10 PSI is the lowest permitted setting for Series PRH. At higher set pressures, the performance gap increases...Series PRH provides the best performance of all known spring-loaded pressure regulators. If even higher performance (near zero drop off) is required, please refer toSeries PRA air loaded pressure regulator.

Maximum Flow Rate & Part Number Reference Chart for Series PRH

flow performance curves of series prh pressure regulator


• Sizes 1/4", 3" & 4" in PVC.
• Size 1/4" in CPVC.
• Sizes 1/4", & 3" (lower pressure range) in Natural Polypro.
• Sizes 1/4", 1/2", 3/4", 1", 1 1/2" in PTFE.
• Sizes 1/4", & 3" in PVDF.
To complete the part number, add the suffix -PV for PVC, -CP for CPVC, -PP for natural polypropylene, -PF for Kynar PVDF, and -TF for PTFE. For example, to order a 1/4" PVC regulator with EPDM seals, the part number is PRH025EP-PV. 4" part numbers are PRH400EP-PV (EPDM seals) and PRH400V-PV (Viton seals).

1/4" - 3" Dimensions

dimensions of series PRH

4" Dimensions

dimensions of 4 inch pressure control valve

For additional dimensional drawings,please click here and refer to PRH prefix and size.

Piping Connections

NPT is standard. For socket, BSP threads, metric, spigot, flare, flange, or other connection options, please consult factory.

4" Regulator Notes

4" size custom built to order; please contact factory for lead times. Valve is shipped on a pallet via common carrier. Valve installation requires additional caution and support commensurate with safe engineering practices. NPT connections have an external (non-wetted) stainless steel reinforcement; for other connections contact factory.


Made in USA. All of the above valves are machined and/or molded and machined, hand assembled, individually inspected, and tested under pressure at our Cedar Grove, NJ headquarters and carry our True Blue 3-Year Warranty. Product photos are representative and actual appearance may vary based on size and materials.

Plast-O-Matic Valves, Inc.1384 Pompton Avenue Cedar Grove,
NJ 07009 USA Phone: (973) 256-3000 Fax: (973) 256-4745
California Warehouse4054 Brewster Way Riverside, CA 92501
USA phone: (951) 686-2852 Fax: (951) 686-6328
Email:info@www.trynanohooks.com Legacy home page:please click here